What are the technical steps and requirements for the installation of LCD splicing screen?

The installation of LCD splicing screen is not like ordinary display equipment, just simply put it on and install it. The installation of LCD splicing screens should not only choose the installation site carefully, but also pay attention to the light around the installation environment, and also need to pay attention to the wiring, and there are also requirements for the frame. When choosing, let’s talk about how to install the LCD splicing screen. So, what are the technical steps and requirements for the installation of LCD splicing screen?

1. Choice of installation ground:
The installation ground for LCD splicing screens should be flat, because the entire system of LCD splicing screens is relatively large in terms of volume and weight. The selected floor also needs to have a certain ability to bear weight. If the floor is tile, it may not be able to bear its weight. Another point is that the installed ground must be anti-static.
2. Cautions for wiring:
When installing the LCD splicing screen, pay attention to distinguishing its power line and signal line when wiring, and install them in different places to avoid interference. In addition, according to the size and installation position of the screen of the entire project, calculate the length and specifications of the various lines needed, and calculate the needs of the entire project.
3. Ambient light requirements:

Although the brightness of the LCD splicing screen is very high, it is still limited after all, so the light around the environment where you choose to install cannot be too strong. If it is too strong, you may not see the picture on the screen. The light that may enter near the screen (such as windows) should be blocked if necessary. At the same time, it is best to turn off the light when the device is running to ensure the normal operation of the device. Do not install a light directly in front of the screen, just install a downlight.


4. Frame requirements:

In order to facilitate the maintenance of the LCD splicing screen in the future, the frame edging must be a detachable edging. A gap of about 25mm is reserved between the inner edge of the outer frame and the outer edge of the splicing wall. For large splicing walls, the margin should be appropriately increased according to the number of columns. In addition, in order to enter the cabinet for maintenance later, the maintenance channel is in principle not less than 1.2m wide. The detachable side strips should preferably be pressed by 3-5mm from the edge of the screen. After the cabinet and the screen are fully installed in place, the detachable side strips are finally fixed.

Share:

Facebook
Twitter
Pinterest
LinkedIn

What are the technical steps and requirements for the installation of LCD splicing screen?

Categories

LED Display Gallery 

Hola LED

Calculation method of simple box size and size of outdoor P8 LED full-color display

The outdoor P8 LED module is placed in a closed box structure to form an outdoor display waterproof box, which is then assembled into an outdoor full-color display with the following structure: Outdoor P8 LED module→Outdoor LED waterproof simple box→Outdoor P8 LED display Outdoor P8 LED module Outdoor P8 LED module Outdoor P8 LED module   Many customers may not understand why the outdoor P8 LED full-color display uses LED simple cabinets to assemble, mainly because the LED waterproof simple cabinets have the following advantages: LED waterproof simple cabinets have advantages First, it is to facilitate scheduling, aging, and on-site

Read More »

Can the P1.87 indoor LED HD display be used as a TV wall?

With the continuous development and improvement of LED technology, indoor LED high-definition displays, especially P1.87 indoor LED HD display, are characterized by seamless splicing, low brightness and high gray, high refresh rate, ultra-high definition, low energy consumption, long life, etc. Many features that conform to market demand and energy-saving economic development advantages have been widely used: power production dispatch control center, military command and control center, urban management emergency command center, traffic management command center, industrial process control display system, radio and television display and monitoring System, shopping mall, hotel, communication information display system, financial securities information display system, government

Read More »

What are the different types of LED displays?

First of all, starting from the color point: single-color, two-color, three-color (full-color) LED display: 1. Monochromatic refers to the luminescent material whose display material has only one color, mostly red. 2. The two-color screen is generally composed of red and green LED diodes. 3. Three-color (full-color) screen, Outdoor LED screen from red… First start from the color point: monochrome, two-color, three-color (full color) LED display: 1.Monochromatic refers to a luminescent material in which the display material has only one color, mostly red. 2.Two-color screens generally consist of red and green LED diodes. 3.Tri-color (full color) screen, consisting of red, green

Read More »

Chinese mini LED manufacturers come back against the wind and are almost on par with the “leader”

Looking back on the past, from CRT to LCD, and then to OLED, every change in display technology will trigger a new round of industrial transformation and reshaping of the competitive landscape on a global scale. It is a pity that Chinese mini LED manufacturers play the role of chasers and followers in the display industry. From “follower” to “leader”, Chinese manufacturers must bet In the history of the development of the LCD panel industry in mainland China, it was a very special transition period. The fate of traditional CRT (cathode ray tube) monitors being replaced by liquid crystal (LCD)

Read More »